Abloy Lock Installation & Rekey Nationwide | Novak Lock & Security Atlanta

Abloy Lock Installation & Rekey in Atlanta: What to Know First

We provide independent Abloy lock installation and rekey services across Atlanta, with most residential jobs completed same-day and commercial keyway projects scheduled within 24 to 48 hours. Rekeying an Abloy cylinder typically runs $85-$140 per core; full lock installation with an Abloy Protec2 deadbolt generally falls between $320-$480, including hardware, labor, and two keys - all quoted in writing before we start. This page is for Atlanta homeowners and property managers who already own Abloy hardware or are considering it, and want a technician who knows the difference between a Protec and a Sento without reading the stamp. Call (470) 944-6813 for a written estimate.

Call (470) 944-6813

How Abloy Products Fail - and How We Fix Them

• Protec2 cylinder rotation lag. The disc detainer mechanism in Protec2 cylinders can develop rotational drag after 6 to 10 years of Atlanta’s humidity cycling, especially in homes near the Chattahoochee with less climate control. We disassemble the core, clean the disc pack with Abloy-specified solvent (not WD-40, which gums the detainer discs), and rekey if the customer has lost a key or terminated a tenant. If the inner disc springs are fatigued, we replace the cylinder rather than patch it.
• Sento keypad battery corrosion. The Sento electronic lock’s battery compartment sits low on the escutcheon, and Atlanta’s summer humidity wicks into the contact points through the seam between housing halves. We find green copper sulfate on the contacts in roughly one of three Sento service calls. Our fix: clean the contacts, apply dielectric grease, and replace with lithium batteries only - alkaline cells leak faster in high humidity. We also check the firmware revision; early Sento units had a power-management bug that accelerates drain.
• Abloy EL560 electric strike misalignment after door settling. In Atlanta’s clay-heavy soils, especially in Grant Park and East Atlanta Village, door frames shift seasonally. The EL560’s precise 1/16-inch keeper tolerance means a frame that was true in March binds by August. We don’t shim the strike and walk away; we rehang the door or reset the frame anchor, then reinstall the strike to factory spec. A misaligned electric strike burns out the solenoid in under a year.
• Protec2 master key system ghosting. When an Atlanta property manager adds a change key to an existing Protec2 master without updating the top-level master pinning, we see “ghost” keys that open unintended doors. This happens because Abloy’s master keying uses a layered disc matrix that requires recalculation of the entire hierarchy. We rebuild the matrix in our shop, rekey every cylinder in the system, and provide a new key register with bitting codes - not just new keys.
• Abloy padlock shackle freeze in unheated storage. The PL330 and PL340 padlocks used on Atlanta construction sites and storage units can bind below 35°F, which matters during January cold snaps when site heaters are off. The cause is factory grease thickening in the shackle bore, not corrosion. We strip the old grease, apply low-temp synthetic lubricant, and rekey if the site has turned over crews. We also flag if the padlock is a standard PL330 in a high-theft zone - the PL340’s hardened shackle is the correct upgrade.

Our Abloy Lock Installation & Rekey Process

1. 1
   Call and scope. A live person answers. We ask for the Abloy model name or a photo of the lock face, the key count, and whether this is a lost-key situation or a planned rekey. The dispatcher quotes a firm price; Haven Standard Clause 1 applies - the price on the phone is the price on the invoice.
2. 2
   On-site diagnostic. The technician arrives in a marked van, uniformed, with a documented photo record starting at the door. We identify the exact Abloy series, check for wear patterns specific to that mechanism, and test every key in the customer’s possession.
3. 3
   Parts decision. For rekeys, we use OEM Abloy pinning kits when available. For discontinued lines, we source quality aftermarket cylinders that match Abloy’s disc detainer geometry without voiding any remaining hardware warranty. We state the origin of every part before installation.
4. 4
   The work. Rekey: remove the cylinder, decode the existing disc stack, rebuild to new key combination, test for shear-line alignment across 50 rotation cycles. Installation: mortise or bore to Abloy’s template, set strike depth, verify deadbolt throw clears the jamb without binding.
5. 5
   Documentation and handoff. The customer receives the new keys, a written scope of work, the photo record from the visit, and the 365-Day Done Right Promise card. We log the bitting code in our secure registry for future rekeying.

What Abloy Lock Installation & Rekey Costs in Atlanta

These are real ranges for the Atlanta market, not teaser rates. The full price is quoted on the phone before anyone is dispatched, and it is the price on the invoice. No call-out surcharge is added on arrival. If you have a competitor’s written estimate, we review it at no charge - Haven Standard Clause 7.

Why Atlanta Homeowners Call Novak Lock & Security Atlanta for Abloy Work

We’ve installed or serviced over 60,000 locks, keys, and systems since 2002, and Abloy’s disc detainer architecture is not a brand every shop stocks or trains on. Our technicians carry Protec2 pinning kits and the specialized tools to decode disc stacks without damaging the cylinder - a common failure point when general locksmiths treat an Abloy like a standard pin-tumbler lock.

The 365-Day Done Right Promise covers every installation and rekey. Background-checked, uniformed technicians work to The Haven Standard, with a documented photo record left with the customer at completion. We also service Schlage, Kwikset, and Medeco, which matters when an Atlanta home has mixed hardware and the owner wants a single point of contact. The name on the van is the warranty.

FAQs